Arduino
Showing all 24 results
-
Arduino
LM393 KY038 High Sensitivity Microphone Sound Detection Sensor
- High Sensitivity Sound Microphone Sensor Detection Module
- The module has two outputs
- AO, analog output, real-time output voltage signal of the microphone
- DO, when the sound intensity reaches a certain threshold, the output high and low signal
- Working Voltage: 5V
SKU: 5487FB8/45 -
Arduino
Passive Buzzer Module
- Buzzer Module consists of a passive piezoelectric buzzer, it can generate tones between 1.5 to 2.5 kHz by switching it on and off at different frequencies either using delays or PWM.
- Operating Voltage : 1.5 ~ 15V DC
- Tone Generation Range : 1.5 ~ 2.5kHz
- Dimensions : 18.5mm x 15mm [0.728in x 0.591in]
SKU: 5487FB8/34 -
Arduino
Soil Hygrometer Detection Module Soil Moisture Sensor
soil humidity module to the environmental humidity is the most sensitive, generally used to detect soil moisture.
module in soil moisture can not reach the setting threshold, DO mouth output high level, when soil moisture more than setting threshold, module D0 output low level;
small plate digital output D0 can be directly connected with the single chip microcomputer, through the single chip microcomputer to detect the high and low level, thus to detect soil moisture;SKU: 5487FB8/29 -
Arduino
Arduino Mega 2560 with Cable
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560. It has 54 digital input/output pins (of which 14 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a reset button.
SKU: 5487FB8/15-1 -
Arduino
Arduino UNO R3 With Atmega328P Microcontroller
Microcontroller : ATmega328
Operating Voltage :5V
Input Voltage (recommended) :7-12V
Input Voltage (limit ) :6-20V
Digital I/O Pins :14 (of which 6 provide PWM output)
Analog Input Pins :6 DC
Current per I/O Pin :40 mA
DC Current for 3.3V Pin : 50 mA
Flash Memory :32 KB (ATmega328) of which 0.5 KB used by bootloader
SRAM :2 KB (ATmega328)
Clock Speed :16 MHzSKU: 5487FB8/15-2 -
Arduino
HC-SR501 Pyroelectric Infrared Sensor Module
The PIR Motion Sensor Detector Module HC-SR501 allows you to sense motion. It is almost always used to detect the motion of a human body within the sensor’s range. It is often referred to using “PIR”, “Pyroelectric”, “Passive Infrared” and “IR Motion” sensor.
SKU: 5487FB8/15-3 -
Arduino
IR Infrared Flame Detection Sensor Module
IR Flame Sensor Module infrared Receiver Ignition source detection module This tiny Flame sensor infrared receiver module ignition source detection module is Arduino compatible can use to detect flame or wavelength of the light source within 760nm~1100nm also useful for Lighter flame detect at the distance 80cm. Greater the flame, farther the test distance.
It has the Detect angle of 60 degrees and very sensitive to flame spectrum. It produces the one channel output signal at D0 terminal for further processing like an alarm system or any switching system. The sensitivity is adjustable with the help of blue potentiometer given on the board.
SKU: 5487FB8/15 -
Arduino
Joy Stick Arduino Joystick PS2 Breakout
Phillips is a two-way rocker 10K resistor, with the joystick in a different direction, tap the resistance vary. This module uses a 5V supply, the original state X, Y readout voltage of 2.5V or so, when pressed with the direction of the arrow, the readout voltage values with increasing, up to 5V; press the arrow in the opposite direction, the readout voltage reduction , a minimum of 0V.
SKU: 5487FB8/15-4 -
-
Arduino
Breadboard Power Supply Module 3.3V 5V
Brand new & high quality
Breadboard power supply module, compatible with 5 V, 3.3 V
Apply to MB102 breadboard
Input voltage: 6.5-12 V (DC) or USB power supply
Output voltage: 3.3V/5V can switch over
Maximum output current: <700 ma
Fluctuation two road independent control, can switch over to 0 V, 3.3 V, 5 VSKU: 5487FB8/09 -
Arduino
Arduino BMP180 Barometric Pressure Sensor Board
- It contains the I2C interface.
- its maximum I2C speed is 3.5Mhz.
- this sensor consists of very low noise which is up to 0.02 hPa or 17cm.
- Its size is 13 x 10 mm.
- Analog devises BMP180 Barometric Sensor for Electronics low-power consumption is -0.5 microamps at 1Hz.
- its pressure range is 300 hPa to 1100 hPa or (9000m to -500m).
SKU: 5487FB8/19 -
Arduino, Servers
DHT11 Temperature and Humidity Sensor
Operating Voltage: 3.5V to 5.5V
Operating current: 0.3mA (measuring) 60uA (standby)
Output: Serial data
Temperature Range: 0°C to 50°C
Humidity Range: 20% to 90%
Resolution: Temperature and Humidity both are 16-bit
Accuracy: ±1°C and ±1%SKU: 5487FB8/06 -
Arduino
433Mhz RF Transmitter and Receiver
433Mhz RF Transmitter Receiver Module best price Pakistan are very cheap and you can use them with any microcontroller (MCU). Which is used in Remote control for cars , or to control simple tasks , like control relay on/off unfortunately I didn’t find What I need , So i decided to write a simple artical about this transceiver and How we can connect it with arduino and program it. These RF modules are very popular among the Arduino tinkerers. The 433MHz is used on a wide variety of applications that require wireless control. This is 433Mhz RF transmitter with receiver kit for Arduino ARM MCU wireless
SKU: 5487FB8/05 -
Arduino
IR Infrared Obstacle Avoidance Sensor Module
IR Infrared Obstacle Avoidance Sensor Module has a pair of infrared transmitting and receiving tubes. When the transmitted light waves are reflected back, the reflected IR waves will be received by the receiver tube. The onboard comparator circuitry does the processing and the green indicator LED comes to life.
The module features a 3 wire interface with Vcc, GND and an OUTPUT pin on its tail. It works fine with 3.3 to 5V levels. Upon hindrance/reflectance, the output pin gives out a digital signal (a low-level signal). The onboard preset helps to fine tune the range of operation, effective distance range is 2cm to 80cm.
SKU: 5487FB8/04 -
Arduino
HC-SR04 Ultrasonic Module HC-SR04
The HC-SR04 ultrasonic sensor uses sonar to determine distance to an object like bats or dolphins do. It offers excellent non-contact range detection with high accuracy and stable readings in an easy-to-use package. From 2cm to 400 cm or 1” to 13 feet. It operation is not affected by sunlight or black material like Sharp rangefinders are (although acoustically soft materials like cloth can be difficult to detect). It comes complete with ultrasonic transmitter and receiver module.
SKU: 5487FB8/02 -
Arduino
Light Sensor Module Optical Photosensitive LDR Module LM393
The module is useful for detecting the presence of light. The module has two LEDs, one for power and one for output of the comparator. In this configuration, the circuit detects if the light exceeds a certain threshold.
SKU: 5487FB8/23 -
Arduino
Adafruit HUZZAH32-ESP32
A feature-rich MCU with integrated Wi-Fi and
Bluetooth connectivity for a wide-range
of applications- 240 MHz dual core Tensilica LX6 microcontroller with 600 DMIPS
- Integrated 520 KB SRAM
- Integrated 802.11b/g/n HT40 Wi-Fi transceiver, baseband, stack and LWIP
- Integrated dual mode Bluetooth (classic and BLE)
- 4 MByte flash include in the WROOM32 module
SKU: 5487FB8/24 -
Arduino
Arduino Pro Mini 3.3&5V
- ATmega328 running at 16MHz with external resonator (0.5% tolerance)
- Low-voltage board needs no interfacing circuitry to popular 3.3V devices and modules (GPS, accelerometers, sensors, etc)
- DC input 5V up to 12V
- Analog Pins: 8, Digital I/Os: 14
- 5V&3V regulator
SKU: 5487FB8/26